Brand new from Vito's Performance This is silencer exhaust packing designed to replaced your old worn out stuff! Made from high density fiberglass, this quiets down any silencers, and last a very long time! Made from high temperature material, this can resist up to 1228 degrees F There is enough ...

This is a set of BRAND NEW rear Yamaha Banshee exhaust pipe silencer hanger mounts These are for TOOMEY pipes - fits T5 T6 or any other Toomey silencer These aftermarket unit are made of billet aluminum, and are anodized black These were for holding the rear silencers to the frame of any year ...

This is a Yamaha Blaster Intake manifold reed block valve seat gasket from VITO's PERFORMANCE This goes between the cylinder and intake reed It replaces Yamaha OEM part # 3JM-13621-00-00 Fits any year 1988 to 2006 Blaster YFS200 Will also fits the models below: 1988 YFS200U AIR FILTER 1989 YFS200W

This is a set of 2 exhaust pipe o-rings for a Yamaha Banshee by Vito's Performance These go up inside the exhaust header pipe, right where it mounts to the cylinder These will fit any year Yamaha Banshee 1987-2006 High temp heat rated - these will hold up against the high heat produced from the ...

This is BRAND NEW intake rubber boot manifold These go right between the cylinder and the carb Fits: Big Bear 350 1987-1999 Kodiak 400 1993-1998 Moto 4 350 1987-1995 Still new in the packaging! Replaces Yamaha OEM part # 1YW-13586-00-00 1YW-13586-01-00 3HN-13586-00-00 3HN-13586-01-00 3HN-13586-02-0

Due to supply issues, Toomey has said that these pipes could take from 4 to 6 months to deliver   This is a set of BRAND NEW Toomey Racing T-5 pipes Brand new, chrome finish, ready to install, complete with rear silencer hangers, and o-rings. You get both header head pipes and both ...

This is an OEM factory genuine Kawasaki carburetor boot manifold This fits a 1988-2011 Bayou 220 or 250 This is OEM part number: 14073-1312

This is a set of 4 pipe springs + 2 exhaust pipe o rings for a Yamaha Banshee These are BLACK in color These are 89mm, and will fit any year Yamaha Banshee 1987-2006 Fits stock and aftermarket exhaust ...

This is a set of TWO (2) high temperature exhaust sleeve pipe clamps for a Yamaha Banshee (any year 1987-2006) These are rated up to 500 degrees, and will not melt! These are made with a 3-ply Silicone Elastomer, with a woven polyester fabric vulcanized and cured In English, that means they are ...

This is for 1 high temperature exhaust sleeve pipe clamp for a Yamaha Banshee (any year 1987-2006) These are rated up to 500 degrees, and will not melt! These are made with a 3-ply Silicone Elastomer, with a woven polyester fabric vulcanized and cured In English, that means they are strong, ...

This is BRAND NEW OEM pair of carb intake boots for a Yamaha Raptor 660 Raptor These go right between the cylinder and the carb You get 2 boots, one left, and one right, with matching o-rings Its ready to install on ANY year Yamaha Raptor 660 660R 2001 20022003 2004 2005 Still new in the ...

This is BRAND NEW OEM carb intake boot flange for a Yamaha Wolverine Kodiak or Grizzly 400 or 450 These go right between the cylinder and the carb You get 1 boot with matching o-ring Still new in the packaging! fits the following models: 2000-2004 YFM400A KODIAK 2WD 2000 KODIAK 2WD ...

This is a BRAND NEW factory snorkel tube for a Yamaha Raptor 660 660R This is the left side This is a genuine OEM factory part directly form Yamaha - new in package In stock, ready to ship from Michigan, ...